pure indoor living Holmes Products (Europe) Ltd. 1 Francis Grove London SW19 4DT England English Français/French 5 13 17 22 26 30 34 38 42 47 52 56 60 65 69 Fax: +44 (0)20 8947 8272 Email: enquiriesEurope@jardencs.com Website address: www.bionaire.com/europe UK - Free phone Customer Service Helpline ­ 0800 052 3615 Holmes Products France 1015, Rue du Maréchal Juin Z.I Vaux - Le - Pénil 77000 Melun ­ France Phone: +33 1 64 10 45 80 Fax: +33 1 64 10 02 32 Deutsch/German Español/Spanish Suomi/Finnish Polski/Polish Svenska/Swedish Nederlands/Dutch Norsk/Norwegian EKKHNIKA/Greek 8 FRANCE - SERVICE CONSOMMATEURS Belgium: Czech Republic: Finland: Germany: Hungary: Latvia Lebanon: Lithuania Netherlands: Norway: Poland: Slovakia: Spain: Sweden: Turkey: United Arab Emirates: +32 38 70 86 86 +420 48 513 03 03 +358 9 8708 7851 +49 89 5480195-0 +36 1 37 17 970 +371 7514081 +961 1 81 49 46 +370 52 772388 +31 79 36 37 310 +47 55982770 +48 23 662 68 01 +421 41 723 47 09 +34 902 051 045 +46 300567370 +90 212 210 99 14 +971 42 97 95 52 2kW ELECTRIC FIREPLACE HEATER MODEL# BEF6500 /Russian Cesky/Czech Português/Portuguese Magyar/Hungarian Italiano/Italian Dansk/Danish © 2010 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All rights reserved. Distributed by Holmes Products (Europe) Ltd., 1 Francis Grove, London SW19 4DT, United Kingdom. Printed in PRC © 2010 Sunbeam Products, Inc. faisant affaires sous le nom de Jarden Consumer Solutions. Tous droits réservés. Distribué par Holmes Products (Europe) Ltd., 1 Francis Grove, London SW19 4DT, United Kingdom. Imprimé en RPC P.N. 139937 INSTRUCTION MANUAL NOTICE D'UTILISATION BEDIENUNGSANLEITUNG MANUAL DE INSTRUCCIONES MANUAL DE INSTRUÇÕES MANUALE D'USO INSTRUCTIEHANDLEIDING BRUKERHÅNDBOK KÄYTTÖOPAS BRUKSANVISNING BRUGERVEJLEDNING INSTRUKCJA ECVEIQIDIO ODGCIXM VQGRGR HASZNÁLATI UTASÍTÁS NÁVOD K OBSLUZE BEF6500 Figure 1 Front A B Figure 3 Q J K Remote Control Figure 4 ENGLISH PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS When using electrical appliances, basic safety precautions should always be taken including the following: 1. Before connecting the heater, check that the voltage indicated on the rating plate corresponds to the main voltage in your home/office. 2. WARNING: In order to avoid overheating, do not cover the heater ( ). 3. DO NOT position the heater directly under a power socket. 4. DO NOT use this heater in the immediate surroundings of a bath, a shower or a swimming pool. 5. If the supply cord or plug is damaged, it must be replaced by the manufacturer or its service agent or similarly qualified person in order to avoid hazard. The heater contains no user serviceable parts. Should the product suffer damage or breakdown, it must be returned to the manufacturer or their service agent. 6. Under the environment with electrical fast transient, the product may malfunction and require user to reset the product. 7. DO NOT use this heater with a programmer, timer, separate remote-control system or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly. 8. Only touch the heater with dry hands. 9. DO NOT position where it can be touched by children, especially the very young. 10. DO NOT use this heater outdoors. 11. Allow a safe area around the heater away from furniture or other objects; at least 50 cm from the top and sides and 200 cm at the front. 12. DO NOT use this heater when it is lying on its side. 13. DO NOT use the heater in rooms with explosive gas (e.g. petrol) or while using inflammable glue or solvent (e.g. when gluing or varnishing parquet floors, PVC etc.). 14. DO NOT insert any objects into the heater. 15. Keep the mains cord at a safe distance from the main body of the heater. 16. If overheating should occur, the built-in overheating safety device will switch off the heater. 17. DO NOT place the cord under a rug. 18. The heater is to be installed so that switches and other controls cannot be touched by a person in the bath. L M Back G 19. Avoid the use of an extension cord because it may cause the heater to overheat. 20. CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility. 21. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless --they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. 22. ( )The remote control contains a magnet to help affix the control to the metal main unit when not in use. Please only place the remote control on the unit where the remote control home is marked (H) DESCRIPTION (SEE FIG. 1, 2, 3, 4, & 6) A. Glass panel B. Pebbles (changeable) C. Light Bulb access panel (contains G9 type 40W max bulb) D. Main housing E. Fixed unit mounting brackets F. Heat vents G. Control panel H. Remote control home I. Feet x 2 (removable) J. Digital thermostat (5 presets) K. Mode control L. Digital timer (6 presets) M. Flame intensity button N. ON/OFF switch (main unit only) O. Thumb screws x 4 P. Securing bottom bracket Q. ON/OFF button remote control ASSEMBLY INSTRUCTIONS (SEE FIG. 1­6) Carefully remove all parts and make sure that they are all present. Ref. to Figs.1-6. Installing Batteries into the Remote: Before operation, insert 2 AAA batteries (not supplied) into the back of the remote control: · DO NOT mix old and new batteries · DO NOT mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries The remote control for this unit has the capability of operating all control panel functions except the BRACKET GUIDE 0 CM THIS IS NOT TO SCALE Fixed Unit Mounting Brackets H C E D Figure 5 57.2 cm 1m 1m Do Not Cover! 1m m inimu m I F Figure 2 J K L M N I O Figure 6 Front BRACKET GUIDE 57.2 CM 5 Wall Mount Installation (See Fig. 4 & 5): This product weighs 16.3 kg. Do not install alone. The following procedure is for a dry wall installation using the provided hardware. Note: If installing on a different type of wall (i.e cavity wall) or using different hardware please consult a professional for advice on the correct way to install the unit. IMPORTANT: Before drilling into any wall ensure no electrical cables are present in the area. Make sure you allow at least 1m of space on all four sides of unit. 1. Turn unit off and disconnect the unit if in use. 2. Remove front glass and pebbles if installed. 3. Remove feet assemblies from main housing by unscrewing the thumb screws. 4. Decide on the position where the electric fireplace will hang on the wall. REMEMBER not to position directly above the power socket and at least 1m away from any objects on all sides (reference Fig. 5). 5. Mark on the wall the points between the centre of the holes on the fixed unit rear mounting brackets (E) making sure the points line up and are level (reference Fig. 4) 6. Drill into the wall using an 8mm drill bit two holes on the marked points so that you can fit the appropriate wall plugs. 7. Screw in two 4 x 35mm screws into the wall plugs, leaving 10mm of the screws out of the wall. 8. Hang the main body of the unit onto the two exposed screws by lining up the rear mounting brackets' holes. 9. Place the securing bottom bracket (P) into the rear of the unit and then use one 4x35mm screw to secure the bracket and unit to the main wall. 10. Add pebbles to the unit, then place the glass panel onto the unit by lining up the glass panel guides with the main housing pins (located on the side of the housing) and make sure the unit is secure. Stand Assembly (See Fig. 6): For floor use attach the two feet assemblies (I) to the fireplace heater using the 4 thumb screws (O) provided. Gently lay the main housing (D) down horizontally without the glass panel attached. Line up each feet assembly using the metal guides and then screw in two thumb screws (O) into the corresponding holes. Place unit upright, add the pebbles (B) and then attach the glass panel by lining up the glass panel metal guides with the main housing panel pins. For wall mounting see Wall Mount Installation below. mechanical ON/OFF switch (N). Please note this remote will not work through walls (See Fig. 3). OPERATING INSTRUCTIONS · There may be an odor coming from the heater the first time you use it. This is normal during the break-in period or after long term storage. Make sure the heater is in a well ventilated area and continue running it until the smell goes away. · You may hear a popping or crackling sound as the heater heats up. This is normal and safe operation. · The Fireplace Heater can be operated by using the remote control (Fig. 3) or the control panel (Fig. 2) located on the side of the unit. · Place the heater on a firm, level surface or mount on wall. · Avoid overloading your circuit by not using other high wattage POWER ON/OFF 1. Turn the main ON/OFF switch (N) on the main unit to the ON (­) position. 2. Either press the mode control (K) or the flame intensity button (M) on the main unit or remote control to start the operation of the unit. 3. If for any reason you would like to turn the unit off press the mode button or flame intensity button on the the ON/Off Button (Q) on the control panel or remote so that no function is heard or visible and then switch the ON/OFF switch on the main unit to the OFF ( ) postion. 11. Unit is now ready to be turned on and operated. selected temperature level by automatically turning the heater ON and OFF. 3. If the heater cycles ON/OFF frequently select a higher preset temperature. 4. To switch the digital thermostat mode off, press the digital thermostat button until the LEDs on digital thermostat setting on the control panel or remote are no longer lit. CLEANING/MAINTENANCE TIMER Note: Timer will work only if one of the three mode settings is used. 1. Press the digital timer button (L) on the control panel or remote enough times to activate one of the 6 preset desired OFF times (2,4,6,8,10 or 12 Hrs) 2. The timer will now turn the unit completely off based on the selected OFF time. 3. To switch the digital timer mode off, press the digital timer button until the LEDs on timer setting on the control panel or remote are no longer lit. 4. Empty the pebbles from the unit. 5. Unscrew the light bulb access panel (C) using a cross head screwdriver, being careful not to lose the screws. 6. Pull out the bulb. 7. Replace the G9 Type bulb with the same type with a 40W max rating. 8. Screw back the light access panel, replace the pebbles and front glass and plug the unit into the power socket for operation. Note: The G9 Type bulb should be readily available from most hardware stores. If not please contact the manufacturer for further assistance. FLAME INTENSITY There are five flame brightness settings, ranging from a low to high setting and then OFF. Press flame intensity button (M) on the control panel or remote control to select desired intensity. Please note that this function works on all modes and is also fully independent. CLEANING AND MAINTENANCE · Always unplug the heater before cleaning and allow to cool. · To clean glass use household glass cleaner. · Lightly run a vacuum cleaner nozzle over the heater vent to remove any dust or dirt that may have accumulated. · Carefully wipe the heater with a soft, damp cloth. Please be very cautious near the heating elements. * NEVER use abrasive or flammable solvents to clean the heater. · After cleaning, be sure to completely dry the heater with a cloth or towel before switching on. · Store your heater in a cool, dry location. TROUBLESHOOTING Flame not bright enough 1. Regulate flame brightness using the flame intensity button. 2. Check bulb is working and replace if necessary. Simulated fire will not illuminate 1. Check power. 2. Press the flame intensity button. 3. Check bulb and replace if necessary. for Fan only setting 1= for continuous low heat (1kW) 2= for continuous high heat (2kW) Press again for no mode operation. MODE SETTINGS Once the main ON/OFF switch has been switched to ON, press the mode control button (K) on the panel or remote control: AUTO SAFETY SHUT OFF This heater is equipped with a technologically advanced safety system that automatically shuts off the current to the heater when a potential overheat temperature is reached. The heater can resume operation only when you reset it and after it has cooled down. RESET INSTRUCTIONS If the unit shuts down: 1. Turn main unit ON/OFF SWITCH to position ( ) (see Fig. 2, N) 2. Unplug unit, wait 30 minutes 3. Plug in the unit 4. Turn main unit ON/O ...