DELTA SANDER PDS 290 A1 DELTA SANDER Operation and Safety Notes Translation of original operation manual SZLIFIERKA DELTA Wskazówki dotyczce obslugi i bezpieczestwa Tlumaczenie oryginalnej instrukcji obslugi DELTACSISZOLÓ Kezelési és biztonsági utalások Az originál használati utasítás fordítása TRIKOTNI BRUSILNIK Navodila za upravljanje in varnostna opozorila Prevod originalnega navodila za uporabo DELTA BRUSKA Pokyny pro obsluhu a bezpecnostní pokyny Peklad originálního provozního návodu DELTA BRÚSKA Pokyny pre obsluhu a bezpecnostné pokyny Preklad originálneho návodu na obsluhu DREIECKSCHLEIFER Bedienungs- und Sicherheitshinweise Originalbetriebsanleitung 4 Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device. Przed przeczytaniem prosz rozloy stron z ilustracjami, a nastpnie prosz zapozna si z wszystkimi funkcjami urzdzenia. Olvasás eltt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik funkcióját. Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave. Ped ctením si otevete stranu s obrázky a potom se seznamte se vsemi funkcemi pístroje. Pred cítaním si odklopte stranu s obrázkami a potom sa oboznámte so vsetkými funkciami prístroja. Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut. GB PL HU SI CZ SK DE / AT / CH Operation and Safety Notes Wskazówki dotyczce obslugi i bezpieczestwa Kezelési és biztonsági utalások Navodila za upravljanje in varnostna opozorila Pokyny pro obsluhu a bezpecnostní pokyny Pokyny pre obsluhu a bezpecnostné pokyny Bedienungs- und Sicherheitshinweise Page Strona Oldal Stran Strana Strana Seite 5 13 23 31 41 49 57 1 2 3 6 5 4 A B 7 8 C 60° 60 ° 60 ° 6 0° D 60 ° 60 ° Table of contents Introduction Proper use .....................................................................................................................Page Features and equipment...............................................................................................Page Included items ...............................................................................................................Page Technical information ...................................................................................................Page 6 6 6 6 General safety advice for electrical power tools 1. Workplace safety .....................................................................................................Page 2. Electrical safety ........................................................................................................Page 3. Personal safety .........................................................................................................Page 4. Careful handling and use of electrical power tools ..............................................Page Safety advice relating specifically to delta sanders ..................................................Page Have you understood everything? ..............................................................................Page 7 7 8 8 9 9 Preparing for use ...............................................................................................Page 9 Vacuum dust extraction ................................................................................................Page Adapter for external vacuum extraction (with reducer piece) ..................................Page Attaching / detaching sanding sheets .........................................................................Page Turn the backing plate in 60° steps ............................................................................Page Advice on use ...............................................................................................................Page 10 10 10 10 11 Maintenance and cleaning ........................................................................Page 11 Service centre .......................................................................................................Page 11 Warranty ..................................................................................................................Page 11 Disposal ......................................................................................................................Page 11 Declaration of Conformity / Manufacturer..................................Page 12 GB 5 Introduction The following pictograms are used in these operating instructions / on the device: Read instruction manual! Observe caution and safety notes! Caution ­ electric shock! Danger to life! Explosive material! Safety class II Wear hearing protection, dust protection mask, protective glasses and protective gloves. Keep children away from electrical power tools! Risk of loss of life by electric shock from damaged mains lead or mains plug! Dispose packaging and appliance in an environmentally-friendly way! V~ W © Volt (AC) Watts (Effective power) © Delta sander PDS 290 A1 Introduction Features and equipment ON / OFF switch Oscillation speed setting wheel Mains lead Dust extraction spout Ventilation openings Backing plate (360° rotatable) Adapter for external vacuum extraction Reducer piece Please make sure you familiarise yourself fully with the way the device works before you use it for the first time and that you understand how to handle electrical power tools correctly. To help you do this please read the accompanying operating instructions. Keep these instructions in a safe place. If you pass the device on to anyone else, please ensure that you also pass on all the documentation. © 1 2 3 4 5 6 7 8 © Included items Proper use The device is intended for dry sanding of wood, plastic, metal, filler and painted surfaces. The device is particularly suitable for corners, profiles or difficult to access places. Any other use or modification to the device shall be considered as improper use and could give rise to considerable dangers. We will not accept liability for loss or damage arising from improper use. Not suitable for commercial use. 1 Delta sander PDS 290 A1 3 Sanding sheets 1 Adapter for external vacuum extraction 1 Reducer piece 1 Operating instructions © Technical information 290 W 230 V~ 50 Hz n0 6000 - 11000 min-1 n0 12000 - 22000 min-1 360° rotatable Nom. power input: Rated voltage: Nominal speed: Nom. oscillation speed: Backing plate: Protection class: 6 GB Introduction / General safety advice for electrical power tools Noise and vibration data: Measured values for noise are determined in accordance with EN 60745. The A-weighted noise level of the electrical power tool are typically: Sound pressure level: 78 dB(A) Sound power level: 89 dB(A) Uncertainty K: 3 dB Wear ear protection! Evaluated acceleration, typical: Hand / arm vibration ah = 6.735 m / s2 Uncertainty K = 1.5 m / s2 WARNING! The vibration level given in these instructions has been measured in accordance with a standardised measurement procedure specified in EN 60745 and can be used to compare devices. Different uses of the device give rise to different vibration levels and in many cases they may exceed the values given in these instructions. It is easy to underestimate the vibration load if the electrical power tool is used regularly in particular circumstances. Note: If you wish to make an accurate assessment of the vibration loads experienced during a particular period of working, you should also take into account the intervening periods of time when the device is switched off or is running but is not actually in use. This can result in a much lower vibration load over the whole of the period of working. (by means of a mains lead) and electrical tools powered by rechargeable batteries (without a mains lead). 1. Workplace safety a) Keep your working area clean and well lit. Untidy or poorly lit working areas can lead to accidents. b) Do not work with the device in potentially explosive environments in which there are inflammable liquids, gases or dusts. Electrical power tools create sparks, which can ignite dusts or fumes. c) Keep children and other people away while you are operating the electrical tool. Distractions can cause you to lose control of the device. 2. Electrical safety a) The mains plug on the device must match the mains socket. The plug must not be modified in any way. Do not use an adapter plug with devices fitted with a protective earth. Unmodified plugs and matching sockets reduce the risk of electric shock. b) Avoid touching earthed surfaces such as pipes, radiators, ovens and refrigerators with any part of your body. There is an increased risk of electric shock if your body is earthed. c) Keep the device away from rain or moisture. Water entering an electrical device increases the risk of electric shock. d) Do not use the mains lead for any purpose for which it was not intended, e.g. to carry the device, to hang up the device or to pull the mains plug out of the mains socket. Keep the mains lead away from heat, oil, sharp edges or moving parts of the device. Damaged or tangled mains leads increase the risk of electric shock. GB 7 General safety advice for electrical power tools WARNING! Read all the safety advice and instructions! Failure to observe the safety advice and instructions may result in electric shock, fire and / or serious injury. Keep all the safety advice and instructions in a safe place for future reference! The term "electrical tool" used in the safety advice refers to electrical tools powered by mains electricity General safety advice for electrical power tools e) When working outdoors with an electrical power tool always use extension cables that are also approved for use outdoors. The use of an extension cable suitable for outdoor use reduces the risk of electric shock. f) Use a residual current device (RCD) for protection if operating the electrical power tool in a moist environment is unavoidable. The use of an RCD reduces the risk of electric shock. hair, clothing and gloves clear of moving parts. Loose clothing, jewellery or long hair can become trapped in moving parts. g) If vacuum dust extraction and collection devices are fitted do not forget to check that they are properly connected and correctly used. The use of these devices reduces the hazard presented by dust. 4. Careful handling and use of electrical power tools a) Do not overload the device. Always use an electrical power tool that is intended for the task you are undertaking. By using the right electrical power tool for the job you will work more safely and achieve a better result. b) Do not use an electrical power tool if its switch is defective. An electrical power tool that can no longer be switched on and off is dangerous and must be repaired. c) Pull the mains plug from the socket before you make any adjustments to the device, change accessories or when the device is put away. This precaution is intended to prevent you from unintentionally starting the device. d) When not in use always ensure that electrical power tools are kept out of reach of children. Do not let anyone use the device if he or she is not familiar with it or has not read the instructions and advice. Electrical power tools are dangerous when they are used by inexperienced people. e) Look after the device carefully. Check that moving parts are working properly and move freely. Check for any parts that are broken or damaged enough to detrimentally affect the functioning of the device. Have damaged parts repaired before you use the device. Many accidents have their origins in poorly maintained electrical power tools. f) Use the electrical power tool, accessories, inserted tools etc. in accordance 3. Personal safety a) Remain alert at all times, watch what you are doing and always proceed with caution. Do not use the device if you are tired or under the influence of drugs, alcohol or medication. One moment of carelessness when using the device can lead to serious injury. b) Wear personal protective equipment and always wear safety glasses. The wearing of personal protective equipment such as dust masks, non-slip safety shoes, safety helmets or ear protectors, appropriate to the type of electrical power tool used and work undertaken, reduces the risk of injury. c) Avoid unintentional operation of the device. Check that the electrical power tool is switched off before you connect it to the mains, pick it up or carry it. Accidents can happen if you carry the device with your finger on the ON / OFF switch or with the device switched on. d) Remove any setting tools or spanners before you switch the device on. A tool or spanner left attached to a rotating part of a device can lead to injury. e) Avoid placing your body in an unnatural position. Keep proper footing and balance at all times. By doing t ...