MULTI-PURPOSE TOOL PMFW 280 A1 MULTI-PURPOSE TOOL Operation and Safety Notes Translation of original operation manual NARZDZIE WIELOFUNKCYJNE Wskazówki dotyczce obslugi i bezpieczestwa Tlumaczenie oryginalnej instrukcji obslugi Kezelési és biztonsági utalások Az originál használati utasítás fordítása MULTIFUNKCIÓS SZERSZÁM Navodila za upravljanje in varnostna opozorila Prevod originalnega navodila za uporabo MULTIFUNKCIJSKO ORODJE Pokyny pro obsluhu a bezpecnostní pokyny Peklad originálního provozního návodu MULTIFUNKCNÍ NÁSTROJ Pokyny pre obsluhu a bezpecnostné pokyny Preklad originálneho návodu na obsluhu MULTIFUNKCNÉ NÁRADIE Bedienungs- und Sicherheitshinweise Originalbetriebsanleitung MULTIFUNKTIONSWERKZEUG 4 Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the device. Przed przeczytaniem prosz rozloy obie strony z ilustracjami, a nastpnie prosz zapozna si z wszystkimi funkcjami urzdzenia. Olvasás eltt kattintson az ábrákat tartalmazó mindkét oldalra és végezetül ismerje meg a készülék mindegyik funkcióját. Pred branjem obe strani s slikami odprite navzven in se nato seznanite z vsemi funkcijami naprave. Ped ctením si odklopte ob dv strany s obrázky a potom se seznamte se vsemi funkcemi pístroje. Pred cítaním si odklopte obidve strany s obrázkami a potom sa oboznámte so vsetkými funkciami prístroja. Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut. GB PL HU SI CZ SK DE / AT / CH Operation and Safety Notes Wskazówki dotyczce obslugi i bezpieczestwa Kezelési és biztonsági utalások Navodila za upravljanje in varnostna opozorila Pokyny pro obsluhu a bezpecnostní pokyny Pokyny pre obsluhu a bezpecnostné pokyny Bedienungs- und Sicherheitshinweise Page Strona Oldal Stran Strana Strana Seite 5 15 25 35 45 55 65 1 2 4 10 3 11 10 9 8 7 6 5 12 13c 13b 13a 13 A B C D E F G H 13c 13b 13a 13 I J Table of contents Introduction Proper use .....................................................................................................................Page Features and equipment...............................................................................................Page Included items ...............................................................................................................Page Technical data...............................................................................................................Page 6 6 6 7 General safety advice for electrical power tools 1. Workplace safety .....................................................................................................Page 2. Electrical safety ........................................................................................................Page 3. Personal safety .........................................................................................................Page 4. Careful handling and use of electrical power tools ..............................................Page Safety advice relating specifically to this multifunction tool .....................................Page Advice on use ...............................................................................................................Page 7 8 8 8 9 10 Assembly Selecting the right tool .................................................................................................Page Changing the attached tool.........................................................................................Page Place a sanding sheet on the backing plate ..............................................................Page Vacuum extraction of dust / debris ..............................................................................Page Connecting a vacuum dust extraction device ............................................................Page 10 11 11 11 11 Bringing into use Switching On / Off .......................................................................................................Page 12 Selecting the oscillation speed ....................................................................................Page 12 Maintenance and cleaning ........................................................................Page 12 Service .........................................................................................................................Page 12 Warranty ..................................................................................................................Page 12 Disposal ......................................................................................................................Page 13 Declaration of Conformity / Manufacturer..................................Page 13 GB 5 Introduction The following pictograms are used in these operating instructions / on the device: Read the operating instructions! Always heed warning labels and safety instructions! Caution - Danger of electric shock! Hazardous voltage ­ danger to life! Explosive material! n0 Rated idle running speed Safety class II Wear hearing protection, dust protection mask, protective glasses and protective gloves. Keep children away from electrical power tools! Risk of loss of life by electric shock from damaged mains lead or mains plug! Dispose packaging and appliance in an environmentally-friendly way! V~ W © Volt (AC) Watts (effective power) Multi-Purpose Tool PMFW 280 A1 Introduction © Features and equipment ON / OFF switch Oscillation speed setting wheel Ventilation slots Clamping plate Metal saw blade Plunge saw blade Backing plate Segment saw blade Scraping knife Clamping screw Allen key Sanding sheet Vacuum dust extraction assembly (3-piece) Housing attachment Vacuum dust extraction duct Ring connector Please make sure you familiarise yourself fully with the way the device works before you use it for the first time and that you understand how to handle electrical power tools correctly. To help you do this please read the accompanying operating instructions. © Proper use The device is intended for sawing, cutting and sanding. The preferred materials on which the device can be used are: wood, plastic, drywalling, non-ferrous metals, fixings (e.g. nails, screws) and wall tiles. It is particularly suitable for working close to edges and precise work. Any other use or modification to the device shall be considered as improper use and could give rise to considerable dangers. We will not accept liability for loss or damage arising from improper use. Not suitable for commercial use. 1 2 3 4 5 6 7 8 9 10 11 12 13 13a 13b 13c © Included items Multi-Purpose Tool PMFW 280 A1 Plunge saw blade Metal saw blade Clamping screw and clamping plate (prefitted) Backing plate 1 1 1 1 1 6 GB Introduction / General safety advice for electrical power tools 1 1 18 1 1 © Segment saw blade Scraping knife Sanding sheets Allen key Operating instructions exceed the values given in these instructions. It is easy to underestimate the vibration load if the electrical power tool is used regularly in particular circumstances. Note: If you wish to make an accurate assessment of the vibration loads experienced during a particular period of working, you should also take into account the intervening periods of time when the device is switched off or is running but is not actually in use. This can result in a much lower vibration load over the whole of the period of working. Technical data Rated power consumption: 280 W Rated voltage: 230 V~ 50 Hz No-load rotational speed: n0 15000 - 21000 min-1 Protection class: Noise and vibration data: Measured values for noise are determined in accordance with EN 60745. The A-weighted noise level of the electrical power tool are typically: Sound pressure level: 85,1 dB(A) Sound power level: 96,1 dB(A) Uncertainty K: 3 dB Wear ear protection! Evaluated acceleration, typical: Hand / arm vibration: < 2,5 m / s2 The total vibration (vector sum of three directions) is calculated in accordance with EN 60745: Sanding: Vibration emission value ah = 6.4 m / s2, Uncertainty K < 2.0 m / s2 Sawing with the plunge saw blade: Vibration emission value ah = 9.9 m / s2, Uncertainty K < 1.5 m / s2 Sawing with the segment saw blade: Vibration emission value ah = 5.0 m / s2, Uncertainty K < 1.5 m / s2 WARNING! The vibration level given in these instructions has been measured in accordance with a standardised measurement procedure specified in EN 60745 and can be used to compare devices. Different uses of the device give rise to different vibration levels and in many cases they may General safety advice for electrical power tools WARNING! Read all the safety advice and instructions! Failure to observe the safety advice and instructions may result in electric shock, fire and / or serious injury. Keep all the safety advice and instructions in a safe place for future reference! The term "electrical tool" used in the safety advice refers to electrical tools powered by mains electricity (by means of a mains lead) and electrical tools powered by rechargeable batteries (without a mains lead). 1. Workplace safety a) Keep your working area clean and well lit. Untidy or poorly lit working areas can lead to accidents. b) Do not work with the device in potentially explosive environments in which there are inflammable liquids, gases or dusts. Electrical power tools create sparks, which can ignite dusts or fumes. c) Keep children and other people away while you are operating the electrical tool. Distractions can cause you to lose control of the device. GB 7 General safety advice for electrical power tools 2. Electrical safety a) The mains plug on the device must match the mains socket. The plug must not be modified in any way. Do not use an adapter plug with devices fitted with a protective earth. Unmodified plugs and matching sockets reduce the risk of electric shock. b) Avoid touching earthed surfaces such as pipes, radiators, ovens and refrigerators with any part of your body. There is an increased risk of electric shock if your body is earthed. c) Keep the device away from rain or moisture. Water entering an electrical device increases the risk of electric shock. d) Do not use the mains lead for any purpose for which it was not intended, e.g. to carry the device, to hang up the device or to pull the mains plug out of the mains socket. Keep the mains lead away from heat, oil, sharp edges or moving parts of the device. Damaged or tangled mains leads increase the risk of electric shock. e) When working outdoors with an electrical power tool always use extension cables that are also approved for use outdoors. The use of an extension cable suitable for outdoor use reduces the risk of electric shock. f) Use a residual current device (RCD) for protection if operating the electrical power tool in a moist environment is unavoidable. The use of an RCD reduces the risk of electric shock. b) Wear personal protective equipment and always wear safety glasses. The wearing of personal protective equipment such as dust masks, non-slip safety shoes, safety helmets or ear protectors, appropriate to the type of electrical power tool used and work undertaken, reduces the risk of injury. Avoid unintentional operation of the device. Check that the electrical power tool is switched off before you connect it to the mains, pick it up or carry it. Accidents can happen if you carry the device with your finger on the ON / OFF switch or with the device switched on. Remove any setting tools or spanners before you switch the device on. A tool or spanner left attached to a rotating part of a device can lead to injury. Avoid placing your body in an unnatural position. Keep proper footing and balance at all times. By doing this you will be in a better position to control the device in unforeseen circumstances. Wear suitable clothing. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves clear of moving parts. Loose clothing, jewellery or long hair can become trapped in moving parts. If vacuum dust extraction and collection devices are fitted do not forget to check that they are properly connected and correctly used. The use of these devices reduces the hazard presented by dust. c) d) e) f) g) 4. Careful handling and use of electrical power tools a) Do not overload the device. Always use an electrical power tool that is intended for the task you are undertaking. By using the right electrical power tool for the job you will work more safely and achieve a better result. b) Do not use an electrical power tool if its switch is defective. An electrical power 3. Personal safety a) Remain alert at all times, watch what you are doing and always proceed with caution. Do not use the device if you are tired or under the influence of drugs, alcohol or medication. One ...