4 Slide & Negative Scanner SND 3600 A1 Slide & Negative Scanner Operating instructions Filmszkenner Használati utasítás KOMPERNASS GMBH BURGSTRASSE 21 · D-44867 BOCHUM www.kompernass.com ID-Nr.: SND 3600 A1-12/10-V3 IAN: 55973 Pístroj na digitalizování negativ Návod k obsluze Cyfrowy skaner do negatywów Instrukcja obslugi Digitalizator negativov Navodila za uporabo Digitalizér negatívov Návod na obsluhu SND 3600 A1 1 2 2x 5 2x 6 3 7 4 Index Introduction . . . . . . . . .2 Information for these operating instructions . . . . . 2 Copyright . . . . . . . . . . . . . . 2 Limited liability . . . . . . . . . . 2 Warnings . . . . . . . . . . . . . . 3 Proper use . . . . . . . . . . . . . 3 Safety . . . . . . . . . . . . . .4 Basic Safety Instructions . . . 4 Setting up and connecting . . . . . . . . . .6 Safety instructions . . . . . . . . Package contents and transport inspection . . . . . . Disposal of the packaging . Requirements for the set-up location . . . . . . . . . . . . . . . Connecting to a computer . 6 6 7 7 8 Starting the ArcSoft MediaImpression 2 programme . . . . . . . . . . . 15 ArcSoft MediaImpression 2 programme . . . . . . . . . . . . 15 Scanning with the ArcSoft MediaImpression 2 programme . . . . . . . . . . . 16 After Use . . . . . . . . . . . . . 19 Cleaning . . . . . . . . . .20 Safety instructions . . . . . . . 20 Cleaning . . . . . . . . . . . . . . 20 Troubleshooting . . . .21 Safety instructions . . . . . . . 21 Malfunction causes and remedies . . . . . . . . . . . . . . 21 Storage/Disposal . . .22 Storage . . . . . . . . . . . . . . . 22 Disposal of the device . . . 22 Appendix . . . . . . . . . .23 Technical data . . . . . . . . . 23 Note regarding the conformity declaration . . . 24 Warranty . . . . . . . . . . . . . 24 Service . . . . . . . . . . . . . . . 25 Importer . . . . . . . . . . . . . . 25 GB Operating components . . . . . . . .14 Handling and operation . . . . . . . . . .14 Inserting film strips . . . . . . 14 Inserting slides . . . . . . . . . 14 SND 3600 A1 1 Introduction GB Introduction Information for these operating instructions These operating instructions are a component of the Slide & Negative Scanner SND 3600 A1 (henceforth designated as the device) and supplies you with important information for intended use, safety and connection as well as operation of the device. The operating instructions must be constantly kept available close to the device. They are to be read and used by anyone assigned to the operation and repairing of the device. Keep these operating instructions and hand them over with the device to any future owners. Copyright This documentation is copyright protected. Any copying and/or printing, including partial copying/printing, as well as reproductions of the diagrams, even in an altered state is only allowed with written permission from the manufacturer. Limited liability All technical information, data and information for connection and operation, contained in these operating instructions correspond to the latest at the time of printing and, to the best of our knowledge, take into account our previous experience and know-how. No claims can be derived from the details, illustrations and descriptions in these instructions. The manufacturer assumes no responsibility for damage caused by failure to observe the instructions, improper use, inappropriate repairs, making unauthorized changes or for using unapproved replacement parts. 2 SND 3600 A1 Introduction Warnings In the current operation instructions the following warnings are used: WARNING A warning of this danger level signifies a possible dangerous situation. If the dangerous situation is not avoided it can lead to injuries. The directives in this warning are there to avoid personal injuries. IMPORTANT A warning of this danger level signifies possible property damage. If the situation is not avoided it can lead to property damage. The directives in this warning are there to avoid property damage. NOTICE A notice signifies additional information that assists in the handling of the device. GB Proper use This device is intended exclusively for the non-commercial use of scanning and digitizing film negatives and slides. This device is not intended for any other use or for uses beyond those mentioned. SND 3600 A1 3 Safety GB WARNING Danger from unintended use! Danger can come from the device if used for unintended purposes and/or other types of use. Use the device exclusively for intended purposes. Observe the procedures described in these operating instructions. Claims of any kind for damage resulting from unintended use will not be excepted. The operator alone bears liability. Safety In this chapter you receive important safety information regarding handling of the device. This device complies with the statutory safety regulations. Improper use can lead to personal injury and property damage. Basic Safety Instructions For safe handling of the device observe the following safety information: Before use check the device for visible external damage. Do not put into operation a device that is damaged or has been dropped. Damaged cables or connections should be replaced by authorized qualified persons or by the customer service department. 4 SND 3600 A1 Safety Persons who, due to their physical, intellectual or motor abilities, are incapable of operating the device safely may only use the device under supervision or direction from a responsible person. Only permit children to use the device under supervision. Repairs should only be carried out by authorized specialist companies or by the customer service department. Incorrect repairs can result in significant dangers for the user. In addition warranty claims become void. A repair to the device during the warranty period may only be carried out by a customer service department authorized by the manufacturer otherwise no additional warranty claims can be considered for subsequent damages. Defective components may only be replaced with original replacement parts. Only by using original replacement parts can you guarantee that the safety requirements are complied with. Do not carry out any unauthorised reconstructions or alterations to the device. Protect the device from moisture and liquid penetration. Do not operate the device in the vicinity of open flames. GB SND 3600 A1 5 Setting up and connecting GB Setting up and connecting Safety instructions WARNING Personal injury and property damage can occur during initial operation of the device! Observe the following safety information to avoid danger: Packaging material should not be used as a play thing. There is a risk of suffocation! Package contents and transport inspection The device is delivered with the following components as standard: Scanner 2 x Slide holder 2 x Negative holder Programme CD Cleaning brush Operating instructions NOTICE Check the contents to make sure everything is there and for visible damage. If the contents are not complete or are damaged due to defective packaging or through transportation contact the service hotline (see the section "Service"). 6 SND 3600 A1 Setting up and connecting Disposal of the packaging The packaging protects the device from transport damage. The packaging materials are selected from the point of view of their environmental friendliness and disposal technology and are therefore recyclable. The recirculation of packaging into the material circuit saves on raw material and reduces generated waste. Dispose of packaging material that is no longer needed according to the regionally established regulations. NOTICE If possible preserve the device's original packaging during the warranty period so that in the case of a warranty claim you can package the device properly for return. GB Requirements for the set-up location For safe and faultless operation of the device the set-up location must fulfill the following provisions: The device must be placed on a firm, flat and level surface. Do not place the device in a hot, wet or very damp environment or in the vicinity of flammable materials. Place the device so that it is not subjected to direct sunlight. SND 3600 A1 7 Setting up and connecting GB Connecting to a computer System prerequisites You will need a computer with a vacant USB port and with the operating system Windows® XP, Windows® Vista or Windows® 7 from the Microsoft® corporation. Installation of the ArcSoft MediaImpression 2 programme NOTICE In these operating instructions only the programme sections are described that you will need for scanning your slides and/or film negatives. You can find further information in the programme's on-line help. The illustrations and descriptions refer to the operating system Microsoft® Windows® 7. The illustration depictions can differ, depending on the display settings, with other operating systems. Insert the supplied programme CD into your computer's CD drive. The window "Automatic playback" will be displayed. Click on the button "run autorun.exe". The installation begins and the start window is displayed. 8 SND 3600 A1 Setting up and connecting NOTICE If you have switched off the autostart function and the installation process does not begin automatically you can start the installation process by double clicking on the file "autorun.exe" in the CD's main directory. GB Click on the button "Arcsoft Software" to install the "ArcSoft MediaImpression 2" programme. The installation wizard will be configured. SND 3600 A1 9 Setting up and connecting The start window of the installation wizard will be displayed. GB Click on the button "Continue >". The window "License agreement" will be displayed. Click on the button "Yes". 10 SND 3600 A1 Setting up and connecting The window for the selection of the installation directory will be displayed. GB Select the desired installation directory and click on the button "Continue >". The window for the selection of the programme folders (Entry in the Windows start menu) will be displayed. Select the desired programme folder and click on the button "Continue >". SND 3600 A1 11 Setting up and connecting GB The programme will be installed and the installation progress will be displayed. The window "Associated file formats" will be displayed. Select the file format that is to be associated with the programme and click on the button "Continue >". 12 SND 3600 A1 Setting up and connecting The display will show that the installation has been completed. GB Click on the button "Finish". The start window will be displayed again. Click on the button "Exit Installation" to exit the installation programme. Connection Connect the USB cable 4 to a USB port on your computer. SND 3600 A1 13 Operating components/Handling ... GB Operating components LED PWR 2 3 4 5 6 7 SCAN button. Slot for film and/or slide holders. USB connection cable. Film holder. Slide holder. Cleaning brush Handling and operation In this chapter you receive important information for the handling and operation of the device. Inserting film strips Release the fastener on the front of the film holder 5 and open the holder. Insert the film strip into the holder correctly orientated. Close the holder making sure that the cover locks into place. Inserting slides Release the fastener on the front of the slide holder 6 and open the holder. Insert a maximum of 3 framed slides, correctly orientated, into the holder. Close the holder making sure that the cover locks into place. 14 SND 3600 A1 Handling and operation Starting the ArcSoft MediaImpression 2 programme Start the ArcSoft MediaImpression 2 programme by double clicking on the programme icon on the desktop or select the corresponding input from the start menu. GB ArcSoft MediaImpression 2 programme 1 2 3 4 There are four options available: 1. Image: Open an available image on the computer or memory medium. 2. Capture: For the scanning of new images 3. Simple reproduction: Fast image editing 4. Image editing tools: Detailed image editing NOTICE In these operating instructions only the programme sections are described that you will need for scanning your slides and/or film negatives. You can find further information in the programme's online help. SND 3600 A1 15 Handling and operation GB Scanning with the ArcSoft MediaImpression 2 programme Connect the device. The LED PWR lights up. Start the ArcSoft MediaImpression 2 programme. Click on the button "Capture". When the programme is first started after the installation a calibration and data collection process takes place. Make sure that no slide or negative holders are inserted into the device. In the displayed information window click on the button "OK" to start calibration and data collection. The first calibration and data collection process can take several minutes. The calibration progress will be displayed. After comple ...